The mechanical vibratory roller is often unable to operate due to the failure of the driving system in the compaction operation. Our company has many years of working experience and many roller models. On the basis of continuous research, we have summarized a lot of practical experience. The vibration system fault of vibratory roller will affect the working process. Today, I will briefly analyze the diagnosis method for this problem, so as to eliminate the fault quickly.

在排除電氣故障后，檢查振動馬達與振動軸的彈性聯軸器和振動軸內潤滑油的狀況。潤滑油過多會使振頻上不去，一般是因馬達組合油封損壞向軸內漏油所致。如果振動軸花鍵套磨損嚴重，也會導致失振故障，此時應對補油壓力、系統工作壓力進行檢測，從而做出診斷。

After removing the electrical fault, check the elastic coupling between the vibration motor and the vibration shaft and the condition of the lubricating oil in the vibration shaft. Too much lubricating oil will make the vibration frequency unable to go up, which is generally caused by the oil leakage into the shaft due to the damage of the motor combined oil seal. If the spline sleeve of the vibrating shaft is seriously worn, it will also lead to vibration loss fault. At this time, the oil make-up pressure and system working pressure shall be detected to make diagnosis.

檢查油泵泄漏量、機械摩擦力大小、傳輸管道的泄漏和堵塞，調節閥的調定壓力和流量正確與否，查明后，應對癥排除。

Check the oil pump leakage, mechanical friction, leakage and blockage of transmission pipeline, and whether the set pressure and flow of regulating valve are correct. After finding out, the symptoms shall be eliminated.

另外，再檢查液壓馬達的本身的容積效率，機械摩擦阻力和背壓力。

In addition, check the volumetric efficiency, mechanical friction resistance and back pressure of the hydraulic motor.

如果液壓馬達因磨損或密封件密封不良而泄漏量加大，或機械摩擦阻力過大，則多是液壓馬達轉速低、轉矩小的原因所在，應進而查明并對癥排除。

If the leakage of the hydraulic motor increases due to wear or poor sealing of seals, or the mechanical friction resistance is too large, it is mostly the reason for the low speed and torque of the hydraulic motor, which should be found out and eliminated.

由于機器的前后振動系統既獨立又相互聯系（共用補油泵），所以可應用"元件置換法"進行診斷。比如，有一輪振頻低時，可將前、后兩馬達的管路互換，若故障已轉移，則表明故障是在泵上，否則是馬達有故障。同樣，對用于變頻操作的排量控制閥也可采用同樣的"互換法"作診斷。

Since the front and rear vibration systems of the machine are independent and interrelated (share the make-up oil pump), the "element replacement method" can be used for diagnosis. For example, when the vibration frequency of one wheel is low, the pipelines of the front and rear motors can be exchanged. If the fault has been transferred, it indicates that the fault is on the pump, otherwise the motor is faulty. Similarly, the same "interchange method" can also be used for diagnosis of displacement control valves used for frequency conversion operation.

振動主油路的啟振初始?jí)毫蛇_(dá)32MPa,其連續工作壓力大振輻時可達20MPa,小振幅時約為12MPa.當發動機在額定轉速下其連續工作壓力大大高于標準值時，則應檢查振動軸的轉動靈活性，即用專用工具旋轉振動軸，使偏心塊處在高位后再釋放，此時振動軸應能擺動幾次，若感覺阻力大，則應更換振動軸軸承。

The initial starting pressure of the vibration main oil circuit can reach 32Mpa, its continuous working pressure can reach 20MPa when the vibration amplitude is large, and it is about 12MPa when the amplitude is small. When the continuous working pressure of the engine at the rated speed is much higher than the standard value, check the rotation flexibility of the vibration shaft, that is, rotate the vibration shaft with a special tool to make the eccentric block in the high position and then release it. At this time, the vibration shaft should be able to swing several times, If the resistance is large, replace the vibration shaft bearing.